Chi è online?
In totale ci sono 20 utenti online: 0 Registrati, 0 Nascosti e 20 Ospiti :: 1 Motore di ricercaNessuno
Il numero massimo di utenti online contemporaneamente è stato 320 il Dom 25 Lug 2021, 13:48
Ultimi argomenti attivi
» Matteo ArnaldiDa correnelvento Oggi alle 19:29
» Camila Giorgi
Da squalo714 Oggi alle 19:03
» Jannik Sinner
Da squalo714 Lun 06 Mag 2024, 20:20
» Lorenzo Musetti
Da squalo714 Lun 06 Mag 2024, 20:15
» correnelvento vs yatahaze
Da yatahaze Dom 05 Mag 2024, 17:08
» Jan Lennard Struff
Da squalo714 Mar 30 Apr 2024, 19:06
» yonex vcore 98
Da nw-t Mar 30 Apr 2024, 17:18
» Head Liquidmetal Instinct
Da correnelvento Lun 29 Apr 2024, 07:16
» il regolamento cosa dice?
Da yatahaze Ven 26 Apr 2024, 17:34
» Foro italico con famiglia al seguito
Da yatahaze Mar 23 Apr 2024, 15:46
» Touchtennis
Da correnelvento Dom 21 Apr 2024, 18:19
» Ibrido per prokennex black ace (300g ovale 100)
Da correnelvento Sab 20 Apr 2024, 14:24
» Scarpe Artengo
Da wetton76 Gio 18 Apr 2024, 23:14
» Corde su Head mp 2022
Da Lucio Gio 18 Apr 2024, 16:28
» Nuove corde per U12/14
Da nw-t Lun 15 Apr 2024, 10:26
» Ibrido per Yonex ezone 98
Da uciambex Dom 14 Apr 2024, 21:59
» Stefanos Tsitsipas
Da squalo714 Dom 14 Apr 2024, 19:34
» Rovesci bimani
Da john mc edberg Dom 14 Apr 2024, 17:09
» inclinazione della racchetta nei vari tipi di servizio
Da felipe Ven 12 Apr 2024, 19:00
» Grigor Dimitrov
Da squalo714 Gio 11 Apr 2024, 23:20
» Tennispro
Da yatahaze Lun 08 Apr 2024, 08:28
» Berrettini
Da yatahaze Lun 08 Apr 2024, 08:27
» Consiglio per cambio racchetta
Da correnelvento Mer 03 Apr 2024, 16:36
» ATP/WTA box
Da felipe Dom 31 Mar 2024, 21:46
» Pro Tennis 480 plus - Problema
Da patillo Dom 31 Mar 2024, 18:22
conversione misure telai
JET method: chi lo conosce?
+8
oedem
Stefano
ultravox
Lupo65
napalm_it
Aerogel
jagui
Federyonex
12 partecipanti
Pagina 1 di 1
JET method: chi lo conosce?
Sul forum di TW, ho trovato un riferimento a questo metodo, a quanto pare una modifica del Jay Cee di John Elliot. Il metodo é inoltre consigliato per incordare delle nuove corde che si chiamano l-tec premium e sono dei poly da incordare a tensioni molto basse.
Qualcuno ne sa qualcosa?
Qualcuno ne sa qualcosa?
Federyonex- Messaggi : 699
Data d'iscrizione : 18.07.11
Re: JET method: chi lo conosce?
Il JET method è "proprietario", ma i concetti di base si sanno:
1) tensioni basse
2) velocità minima del tensionatore
3) lasciare in tensione 5-10 secondi prima di pinzare
1) tensioni basse
2) velocità minima del tensionatore
3) lasciare in tensione 5-10 secondi prima di pinzare
jagui- Messaggi : 316
Data d'iscrizione : 19.05.11
Età : 51
Località : Roma
Re: JET method: chi lo conosce?
non sai se da qualche parte si trova uno scritto o un video esemplificativo del metodo?
So che Elliot fa dei corsi a parigi, ma costano 1000€ e mi pare pura speculazione, checché ne dicano gli adepti di blog come quelli di guts and glory.
So che Elliot fa dei corsi a parigi, ma costano 1000€ e mi pare pura speculazione, checché ne dicano gli adepti di blog come quelli di guts and glory.
Oedem : le racchette migliori sono quelle che hanno le corde
Federyonex- Messaggi : 699
Data d'iscrizione : 18.07.11
Aerogel- Messaggi : 401
Data d'iscrizione : 03.05.11
Località : Roma - Gaeta
Re: JET method: chi lo conosce?
si, ma poco esaustive, Aero. In pratica:
-usa tensioni basse <20kg
-tensiona alla minor velocità possibile
-lascia in trazione la corda prima della clampatura per 10 s
e basta.
Possibile che chiedano 1000€ per ste 4 stronzate?
-usa tensioni basse <20kg
-tensiona alla minor velocità possibile
-lascia in trazione la corda prima della clampatura per 10 s
e basta.
Possibile che chiedano 1000€ per ste 4 stronzate?
Oedem : le racchette migliori sono quelle che hanno le corde
Federyonex- Messaggi : 699
Data d'iscrizione : 18.07.11
Re: JET method: chi lo conosce?
Secondo me guts & glory eccelle soprattutto nel marketing.
Lo dicono da anni e anni le stesse case produttrici dei monofili che questi vanno incordati lentamente e a tensioni basse.
Mi sembra anche che stefano abbia accennato qualcosa a riguardo qui da qualche parte, ma non mi ricordo minimamente dove (anche se qualcosa mi dice che non seguirebbe questi consigli perchè preferisce andare veloce).
Eiffel anche ne parla da tempo.
Secondo me è un segreto di pulcinella, cose gli incordatori di alto livello sanno da tempo, e che questi di guts & glory hanno impacchettato in un nuovo prodotto/servizio.
Tipica operazione di marketing.
Lo dicono da anni e anni le stesse case produttrici dei monofili che questi vanno incordati lentamente e a tensioni basse.
Mi sembra anche che stefano abbia accennato qualcosa a riguardo qui da qualche parte, ma non mi ricordo minimamente dove (anche se qualcosa mi dice che non seguirebbe questi consigli perchè preferisce andare veloce).
Eiffel anche ne parla da tempo.
Secondo me è un segreto di pulcinella, cose gli incordatori di alto livello sanno da tempo, e che questi di guts & glory hanno impacchettato in un nuovo prodotto/servizio.
Tipica operazione di marketing.
jagui- Messaggi : 316
Data d'iscrizione : 19.05.11
Età : 51
Località : Roma
Re: JET method: chi lo conosce?
I 1000 euro li chiederanno per indottrinarti sul come ascoltare e consigliare i clienti e sul come proporre a questi le proprie soluzioni.
jagui- Messaggi : 316
Data d'iscrizione : 19.05.11
Età : 51
Località : Roma
Re: JET method: chi lo conosce?
sì, mi pare di ricordare tempo fà Stef disse di lasciare passare qualche secondo prima di pinzare la corda in tensione... se nn erro.
ovviamente in ambiente negozio o sala incordature di torneo queste cose nn si possono fare per via del tempo.
ovviamente in ambiente negozio o sala incordature di torneo queste cose nn si possono fare per via del tempo.
napalm_it- Messaggi : 1418
Data d'iscrizione : 17.02.11
Età : 44
Località : Prov nord Torino
Re: JET method: chi lo conosce?
Si crea una sorta di pre-stretch, ma se non lo richiedono i pro...perche' mai farlo? Da un lato riduci l'effetto della perdita di tensione iniziale, dall'altro riduci la vita dinamica della corda.
Lupo65- Moderatore
- Messaggi : 5077
Data d'iscrizione : 17.01.11
Età : 58
Località : Kinross-shire
Re: JET method: chi lo conosce?
A quanto pare è stato pubblicato:
JET Method - your Online Guide to How and Why?
Many of our blog followers are likely aware that Tennis Warehouse has picked up L-TEC Premium strings to make available to internet customers. The purpose of today’s blog entry is to give those who are purchasing L-TEC Premium strings online the means to string them so that they can achieve the best possible results. Toward this end we are proud to present the JET Method of stringing for constant pull stringing machines using fixed clamps.
OVERVIEW :
The JET Method of stringing combined with L-TEC Premium strings provide players with an equipment advantage delivering the best possible on-court results.
There are 3 major components of the method that should be implemented in unison to achieve optimal results.
Analyzing and calculating the player’s ideal string bed tension.
Choosing the best L-TEC Premium string(s) to improve the player’s game.
Applying the exact set tensions and the JET Method of stringing to achieve the precise overall string-bed tension required by the player.
There is a very precise methodology and tools that allow the stringer to string at lower tensions. The stringing technique/method preserves the elasticity of the string and ultimately allows the string bed to hold the desirable playing properties for an extended period of time.
REFERENCE TENSION :
Twenty-four hours after stringing a racquet the overall string-bed tension will measure from -4lbs to -6lbs lower than the tension that was originally set on the machine.
After 1 hour of play there will be a further loss of tension of at least -2lbs.
The JET Method of stringing progressively increases the overall string-bed tension up to 3lbs higher than the SET Tension on the machine for a 16*19 string pattern and up to 5lbs higher for a 18*20 string-pattern.
Therefore, to obtain a similar overall string-bed tension when using the JET Method, the Reference SET tension should be reduced from -7lbs to -10lbs depending on the machine and the string-pattern. The Reference SET Tension on the machine is much lower, but the feeling of stiffness in the string-bed will be quite comparable. The vastly improved comfort, power, control and spin, as well as the capacity to hold tension and maintain an initial playability for much longer than usual stringing methods, are the most evident advantages of the JET Method of stringing.
RACQUET PREPARATION :
If necessary, carefully use an awl to enlargen the grommet holes on #6 main (16 main pattern) or #7 main (18 main pattern) for tie-off. (This will be either top or bottom depending on where main strings end.)
Enlargen the grommet hole on the third cross from bottom of frame for tie-off. (Depending on pattern, this can sometimes vary. The objective is to tie-off as close to the 2nd to last cross as possible).
MAIN STRINGS :
String first four center mains on each side at reference tension.
Next 2 (on 16 mains) or 3 (on 18 mains) reduce tension by -4lbs.
On a 16 main pattern after pulling main #6 skip over to #8. Increase tension +4lbs (to reference tension) before tensioning. (#8 will be pulled at reference tension). On an 18 main pattern after pulling #7 skip over to #9. Increase tension +4lbs before tensioning.
Fill-in main #7 (on a 16 main or #8 on an 18 main) which will be the last main. Adjust tension by adding an additional 4lbs (reference tension +4lbs.)
Tie off on main #6 (16 mains) or #7 (18 mains).
CROSS STRINGS :
IMPORTANT: Each cross string must be held under tension at least 20 seconds before clamping off. We recommend weaving the next cross while the previous one remains under tension.
Start first three cross strings at same tension applied to the last main string tensionned before tie-off on each side. (+4lbs over the reference tension)
After installing 3rd cross string, reduce tension -6lbs and install the rest of the cross strings (This will be reference tension –2lbs)
After stringing 3rd last cross, loop over and weave final cross. Increase tension +6lbs.
For last cross string fill in second from bottom. Tie off on 3rd cross from the bottom.
Always give professional finish by straightening strings using The String Thing!
Some points to keep in mind :
This presentation of the JET Method is intended for stringers using an electronic constant pull stringing machine with fixed clamps.
In the quest for stringing perfection, this is not the ideal stringing machine. However, by using the JET Method conscientiously the results can be remarkably good.
If you have the choice of pulling speeds, always select the slowest.
Wait 5 seconds before clamping off each main and a minimum of 20 seconds before clamping each of the crosses. (weave in the following cross whilst the previous cross is being tensionned, this can save a lot of time).
To become a competant stringer capable of giving top quality string-jobs when applying the JET Method requires many hours to learn and to practice this craft. It is necessary to control the results obtained string by string with a Stringmeter to understand where you are losing tension and where you need to improve your techniques to overcome these weaknesses in your way of working.
To aim for the end results on the court for your player requires strong motivation and real passion for your profession. Without your will to improve as a stringer and the capacity to put into question your habits in the way you have been stringing for years, you will not be able to acquire the efficiency in this craft necessary to obtain JET Method Certification. You may well improve your results for your players and that would be a very good start, it may even encourage you to continue to learn to become a much better stringer, even a craftsman. Now it's up to you!
JET Method - your Online Guide to How and Why?
Many of our blog followers are likely aware that Tennis Warehouse has picked up L-TEC Premium strings to make available to internet customers. The purpose of today’s blog entry is to give those who are purchasing L-TEC Premium strings online the means to string them so that they can achieve the best possible results. Toward this end we are proud to present the JET Method of stringing for constant pull stringing machines using fixed clamps.
OVERVIEW :
The JET Method of stringing combined with L-TEC Premium strings provide players with an equipment advantage delivering the best possible on-court results.
There are 3 major components of the method that should be implemented in unison to achieve optimal results.
Analyzing and calculating the player’s ideal string bed tension.
Choosing the best L-TEC Premium string(s) to improve the player’s game.
Applying the exact set tensions and the JET Method of stringing to achieve the precise overall string-bed tension required by the player.
There is a very precise methodology and tools that allow the stringer to string at lower tensions. The stringing technique/method preserves the elasticity of the string and ultimately allows the string bed to hold the desirable playing properties for an extended period of time.
REFERENCE TENSION :
Twenty-four hours after stringing a racquet the overall string-bed tension will measure from -4lbs to -6lbs lower than the tension that was originally set on the machine.
After 1 hour of play there will be a further loss of tension of at least -2lbs.
The JET Method of stringing progressively increases the overall string-bed tension up to 3lbs higher than the SET Tension on the machine for a 16*19 string pattern and up to 5lbs higher for a 18*20 string-pattern.
Therefore, to obtain a similar overall string-bed tension when using the JET Method, the Reference SET tension should be reduced from -7lbs to -10lbs depending on the machine and the string-pattern. The Reference SET Tension on the machine is much lower, but the feeling of stiffness in the string-bed will be quite comparable. The vastly improved comfort, power, control and spin, as well as the capacity to hold tension and maintain an initial playability for much longer than usual stringing methods, are the most evident advantages of the JET Method of stringing.
RACQUET PREPARATION :
If necessary, carefully use an awl to enlargen the grommet holes on #6 main (16 main pattern) or #7 main (18 main pattern) for tie-off. (This will be either top or bottom depending on where main strings end.)
Enlargen the grommet hole on the third cross from bottom of frame for tie-off. (Depending on pattern, this can sometimes vary. The objective is to tie-off as close to the 2nd to last cross as possible).
MAIN STRINGS :
String first four center mains on each side at reference tension.
Next 2 (on 16 mains) or 3 (on 18 mains) reduce tension by -4lbs.
On a 16 main pattern after pulling main #6 skip over to #8. Increase tension +4lbs (to reference tension) before tensioning. (#8 will be pulled at reference tension). On an 18 main pattern after pulling #7 skip over to #9. Increase tension +4lbs before tensioning.
Fill-in main #7 (on a 16 main or #8 on an 18 main) which will be the last main. Adjust tension by adding an additional 4lbs (reference tension +4lbs.)
Tie off on main #6 (16 mains) or #7 (18 mains).
CROSS STRINGS :
IMPORTANT: Each cross string must be held under tension at least 20 seconds before clamping off. We recommend weaving the next cross while the previous one remains under tension.
Start first three cross strings at same tension applied to the last main string tensionned before tie-off on each side. (+4lbs over the reference tension)
After installing 3rd cross string, reduce tension -6lbs and install the rest of the cross strings (This will be reference tension –2lbs)
After stringing 3rd last cross, loop over and weave final cross. Increase tension +6lbs.
For last cross string fill in second from bottom. Tie off on 3rd cross from the bottom.
Always give professional finish by straightening strings using The String Thing!
Some points to keep in mind :
This presentation of the JET Method is intended for stringers using an electronic constant pull stringing machine with fixed clamps.
In the quest for stringing perfection, this is not the ideal stringing machine. However, by using the JET Method conscientiously the results can be remarkably good.
If you have the choice of pulling speeds, always select the slowest.
Wait 5 seconds before clamping off each main and a minimum of 20 seconds before clamping each of the crosses. (weave in the following cross whilst the previous cross is being tensionned, this can save a lot of time).
To become a competant stringer capable of giving top quality string-jobs when applying the JET Method requires many hours to learn and to practice this craft. It is necessary to control the results obtained string by string with a Stringmeter to understand where you are losing tension and where you need to improve your techniques to overcome these weaknesses in your way of working.
To aim for the end results on the court for your player requires strong motivation and real passion for your profession. Without your will to improve as a stringer and the capacity to put into question your habits in the way you have been stringing for years, you will not be able to acquire the efficiency in this craft necessary to obtain JET Method Certification. You may well improve your results for your players and that would be a very good start, it may even encourage you to continue to learn to become a much better stringer, even a craftsman. Now it's up to you!
ultravox- Messaggi : 24
Data d'iscrizione : 07.01.12
Re: JET method: chi lo conosce?
... In sostanza è un JayCee con tempi piú lunghi di trazione della corda.
Certo che almeno 20" di trazione per ogni orizzontale!!! Non ti passa piú
Certo che almeno 20" di trazione per ogni orizzontale!!! Non ti passa piú
Oedem : le racchette migliori sono quelle che hanno le corde
Federyonex- Messaggi : 699
Data d'iscrizione : 18.07.11
Re: JET method: chi lo conosce?
No Bruno, non e' simile al methodo di JayCee, ma E' il metodo di JayCee.
JET significa JOHN ELLIOT TECHNIQUE. John Elliot e' JayCee.
E' un metodo che funziona sicuramente, ma va bene per chi, come John, sta a casa tutto il giorno! Io, dal 10 gennaio scorso a oggi, ho incordato piu' di 500 telai. Se aspettassi 20 secondi per ogni corda,finirei l'anno prossimo!
JET significa JOHN ELLIOT TECHNIQUE. John Elliot e' JayCee.
E' un metodo che funziona sicuramente, ma va bene per chi, come John, sta a casa tutto il giorno! Io, dal 10 gennaio scorso a oggi, ho incordato piu' di 500 telai. Se aspettassi 20 secondi per ogni corda,finirei l'anno prossimo!
Direttore Tecnico IRSA - USRSA MRT - ERSA Pro Tour Stringer - UKRSA Tournament Stringer - Membro onorario CRSA
La mia racchetta e' li' solo per tenere le corde.
Boris Becker
Stefano- Messaggi : 4584
Data d'iscrizione : 01.11.10
Età : 60
Località : Melbourne-Australia
Re: JET method: chi lo conosce?
Stefano ha scritto:No Bruno, non e' simile al methodo di JayCee, ma E' il metodo di JayCee.
JET significa JOHN ELLIOT TECHNIQUE. John Elliot e' JayCee.
E' un metodo che funziona sicuramente, ma va bene per chi, come John, sta a casa tutto il giorno! Io, dal 10 gennaio scorso a oggi, ho incordato piu' di 500 telai. Se aspettassi 20 secondi per ogni corda,finirei l'anno prossimo!
Lupo65- Moderatore
- Messaggi : 5077
Data d'iscrizione : 17.01.11
Età : 58
Località : Kinross-shire
Re: JET method: chi lo conosce?
ecco Stefano dopo la prima incordatura:Stefano ha scritto:.....Se aspettassi 20 secondi per ogni corda,finirei l'anno prossimo!
ho l'occhio di pulcinella
Con il polibutilene ogni colpo riesce bene!
(cit. by Satrapo)
oedem- Messaggi : 6053
Data d'iscrizione : 01.12.09
Re: JET method: chi lo conosce?
Ste, intendevo che ha solo rinominato il suo stesso metodo per renderlo piú commerciale e legarlo alle L-tec come fosse la combinazione vincente della lotteria del bel gioco tennistico
Oedem : le racchette migliori sono quelle che hanno le corde
Federyonex- Messaggi : 699
Data d'iscrizione : 18.07.11
Re: JET method: chi lo conosce?
Testate anche quelle (usando il suo metodo) oltre a quasi tutte le Thundrstring: due o tre modelli sono interessanti anche in ibrido. Se si considera il prezzo preferisco usare le più note perchè il rapporto qualità/prezzo non è vantaggioso più di tanto. Poi come dice Stefano, i tempi di incordatura sono alti, di conseguenza anche i costi.Federyonex ha scritto:Ste, intendevo che ha solo rinominato il suo stesso metodo per renderlo piú commerciale e legarlo alle L-tec come fosse la combinazione vincente della lotteria del bel gioco tennistico
Simba- Messaggi : 3971
Data d'iscrizione : 29.04.11
Località : Verona
Re: JET method: chi lo conosce?
Impiegare tra i 45 e i 60 minuti a telaio non è conveniente nemmeno per chi fa 10 racchette a settimana, perché a quel punto quello che è un diversivo da un'ora al giorno per cinque giorni diventa una specie di part-time da 10 ore!!!
Per funzionare il metodo funziona, ma bisogna selezionare bene gli armeggi e comunque rimango dell'idea che non tutti i tipi di giocatori ne possano trarre profitto.
E anche chi potrebbe trovare giovamento sul campo IMHO non sarebbe mai e poi mai disposto a pagare al proprio incordatore il doppio della manodopera
Per funzionare il metodo funziona, ma bisogna selezionare bene gli armeggi e comunque rimango dell'idea che non tutti i tipi di giocatori ne possano trarre profitto.
E anche chi potrebbe trovare giovamento sul campo IMHO non sarebbe mai e poi mai disposto a pagare al proprio incordatore il doppio della manodopera
TennisTest.it
Aerogel- Messaggi : 401
Data d'iscrizione : 03.05.11
Località : Roma - Gaeta
Re: JET method: chi lo conosce?
Aerogel ha scritto:Impiegare tra i 45 e i 60 minuti a telaio non è conveniente nemmeno per chi fa 10 racchette a settimana, perché a quel punto quello che è un diversivo da un'ora al giorno per cinque giorni diventa una specie di part-time da 10 ore!!!
Per funzionare il metodo funziona, ma bisogna selezionare bene gli armeggi e comunque rimango dell'idea che non tutti i tipi di giocatori ne possano trarre profitto.
E anche chi potrebbe trovare giovamento sul campo IMHO non sarebbe mai e poi mai disposto a pagare al proprio incordatore il doppio della manodopera
Simba- Messaggi : 3971
Data d'iscrizione : 29.04.11
Località : Verona
Re: JET method: chi lo conosce?
Stefano ha scritto:No Bruno, non e' simile al methodo di JayCee, ma E' il metodo di JayCee.
JET significa JOHN ELLIOT TECHNIQUE. John Elliot e' JayCee.
E' un metodo che funziona sicuramente, ma va bene per chi, come John, sta a casa tutto il giorno! Io, dal 10 gennaio scorso a oggi, ho incordato piu' di 500 telai. Se aspettassi 20 secondi per ogni corda,finirei l'anno prossimo!
Stefano sai, non ci volevo credere ma io piu' velocemente mi incordo la racchetta e meglio ci gioco, alla faccia dei 20 secondi a trazione
cobrama- Messaggi : 2250
Data d'iscrizione : 20.01.11
Età : 57
Località : toscana
Re: JET method: chi lo conosce?
Oggi ho incordato due APD con stessa corda(black mamba 1.25),stessa tensione(23Kg) ma usando un modified box per una ed il JET per l'altra.
Premetto che incordo con una manuale ed i risultati che ho ottenuto con racquetTune sono completamente diversi:
APD1(modified box),tensione letta=22.2Kg e DT=33.8
APD2(JET),tensione=24Kg e DT=37
Com'è possibile?
Maurizio
Premetto che incordo con una manuale ed i risultati che ho ottenuto con racquetTune sono completamente diversi:
APD1(modified box),tensione letta=22.2Kg e DT=33.8
APD2(JET),tensione=24Kg e DT=37
Com'è possibile?
Maurizio
ultravox- Messaggi : 24
Data d'iscrizione : 07.01.12
Re: JET method: chi lo conosce?
Boh, forse dipende dal fatto che il contrappeso continua a scendere lentamente, magari in modo impercettibile, quando lasci le O in trazione 20 sec o giú di li.
Questo potrebbe tendere piú del voluto la corda...
Questo potrebbe tendere piú del voluto la corda...
Oedem : le racchette migliori sono quelle che hanno le corde
Federyonex- Messaggi : 699
Data d'iscrizione : 18.07.11
Re: JET method: chi lo conosce?
Tiè... beccateve 'sto spiccio
http://www.tennistest.it/2012/04/jet-method-provato/
Vi avverto che è parecchio lungo, ma abbiamo voluto fare le cose per bene.
Manca purtroppo un ingrediente essenziale, cioè le corde L-TEC.
Ma se siete curiosi di sapere che succede quando si utilizzano due corde "normali"... siete serviti
Unica perplessità, le rilevazioni sulla tenuta di tensione che non mostrano miglioramenti con il JET, a differenza di quanto avevo già visto tempo fa e di quanto mi aspetterei di base. Farò altri tentativi.
Anche perché se la corda non tiene più a lungo, dopo 6 - 7 ore ci si ritrova con un piatto corde troppo poco consistente!
http://www.tennistest.it/2012/04/jet-method-provato/
Vi avverto che è parecchio lungo, ma abbiamo voluto fare le cose per bene.
Manca purtroppo un ingrediente essenziale, cioè le corde L-TEC.
Ma se siete curiosi di sapere che succede quando si utilizzano due corde "normali"... siete serviti
Unica perplessità, le rilevazioni sulla tenuta di tensione che non mostrano miglioramenti con il JET, a differenza di quanto avevo già visto tempo fa e di quanto mi aspetterei di base. Farò altri tentativi.
Anche perché se la corda non tiene più a lungo, dopo 6 - 7 ore ci si ritrova con un piatto corde troppo poco consistente!
TennisTest.it
Aerogel- Messaggi : 401
Data d'iscrizione : 03.05.11
Località : Roma - Gaeta
Re: JET method: chi lo conosce?
Ciao a tutti.Qui negli usa e abbastanza famoso come metodo ma non veramante usato perce' impiega molto tempo, comunque il Jet method e' stato creato da Jay Cee. cosa basilare oltre a differenziare la tensione tra corda e corda sia delle verticali e orizzontali e' l'uso di una fly clap che riesce a trattenere la tensione di due corde nello stesso momento. Altra cosa e' che jay cee una volta tirata una corda ci preme sopra con un dito.....e' difficile da spiegare. io sono riuscito a ettere la mani su quella che mi haddo detto di essere il metodo completo e piu' accuarto(e' in francese e di qualche tempo fa') e magari se siete interessati lo allego. io ho provato questo metodo anche se non ho quel tipo di fly clamp( ho usato 3 fly clamps per ottenere lo stesso risultato) e devo dire che magari mi e' riuscito, forse per caso ma ho notato la differenza.
Pmano- Messaggi : 51
Data d'iscrizione : 29.03.12
Località : Modena provincia/ USA
Re: JET method: chi lo conosce?
Sapete come si allegano donumenti in PDF, altrimenti non riesco ad allegare in Jay cee metodo. l'ho ricevuto tramite email.
Pmano- Messaggi : 51
Data d'iscrizione : 29.03.12
Località : Modena provincia/ USA
Re: JET method: chi lo conosce?
Pmano ha scritto:Sapete come si allegano donumenti in PDF, altrimenti non riesco ad allegare in Jay cee metodo. l'ho ricevuto tramite email.
Ti conviene caricarlo su un server esterno ( tipo http://imageshack.us/ ) e poi linkarlo
J
janko60- Messaggi : 2695
Data d'iscrizione : 07.10.10
Località : Di là da l'aghe
Argomenti simili
» Footwork: The Bailey Method
» Chi le conosce?
» chi le conosce ?
» [SOLINCO] Chi le conosce ?
» Qualcuno la conosce?
» Chi le conosce?
» chi le conosce ?
» [SOLINCO] Chi le conosce ?
» Qualcuno la conosce?
Pagina 1 di 1
Permessi in questa sezione del forum:
Non puoi rispondere agli argomenti in questo forum.